A Complete Guide to LED Drivers - LEDYi Lighting

As energy laws have gotten stricter, most people know that LEDs, or light-emitting diodes, last a long time and save energy. But few people understand that these high-tech light sources can’t work without an LED driver. LED drivers, sometimes called LED power supplies, are like ballasts for fluorescent lights or transformers for low-voltage bulbs. They give LEDs the electricity they need to run and work at their best.

Read more

What Is An LED Driver?

An LED driver controls how much power an LED or a group of LEDs needs. Since light-emitting diodes are low-energy lighting devices with long life and low energy use, they need specialized power sources.

The main jobs of LED drivers are to provide low voltage and protect LEDs.

Each LED can use up to 30mA of current and work at voltages of about 1.5V to 3.5V. Multiple LEDs can be used in series and parallel to make home lighting, which may need a total voltage of 12 to 24 V DC. The LED driver turns the AC around to meet the needs and lowers the voltage. This means that the high AC mains voltage, which ranges from 120V to 230V, must be changed into the low DC voltage that is needed.

The LED drivers also protect the LEDs from changes in voltage and current. Even if the mains supply changes, the circuits ensure that the voltage and current going to the LEDs stay in the suitable range for them to work. The protection stops the LEDs from getting too much voltage and current, which would hurt them, or insufficient current, making them less bright.

How Do LED Drivers Work?

When the temperature of an LED changes, so do its forward voltage needs. As it gets hotter, less voltage is needed to move current through the LED, so it uses more power. Thermal runaway is when the temperature goes up out of control and burns out an LED. The power output levels on LED drivers are made to meet the needs of LEDs. The driver’s constant current keeps the temperature stable by responding to changes in the forward voltage.

What Is An LED Driver Used For?

Transformers for low-voltage light bulbs do the same thing that LED drivers do for LEDs. LED lights are low-voltage devices that usually run on 4V, 12V, or 24V. To work, they need a source of direct current power. But because wall socket power supplies typically have a much higher Voltage (between 120V and 277V) and produce alternating current, they are not directly compatible. Since the average voltage of an LED is too low for a regular transformer, special LED drivers are used to convert high-voltage alternating current to low-voltage direct current.

The other thing that LED drivers do is protect against power surges, and changes, which can make temperatures rise and light output go down. LEDs are made to only work within a specific range of amps.

Some LED drivers can also change the brightness of the connected LED systems and the order in which the colors are shown. To do this, you must carefully turn each LED on and off. For example, white lights are usually made by turning on a bunch of different-colored LEDs at the same time. If you turn off some of the LEDs, the white color disappears.

Various Dimensions To Describe LED Drivers.

•  External vs. Internal LED Driver

Differences between external and internal LED drivers can be built into lamps (interior), put on the surfaces of light fixtures, or even put outside of them (External). Most low-power indoor lights, especially bulbs, have LED drivers built in. This makes the lights cheaper and more attractive. On the other hand, downlights and panel lights usually have LED drivers on the outside.

When using a lot of power, like street lights, floodlights, stadium lights, and grow lights, external LED drivers are used more and more. This is because the heat inside the lights gets worse as the power goes up. Another good thing about external LED drivers is they can be easily changed for maintenance.

• Switching Power Supply vs. Linear Regulator

Because linear LED drivers are so simple, a resistor, a controlled MOSFET, or an IC may be all needed to make an LED’s constant current. A lot of AC LED, sign, and strip applications use them. Because of this, power supplies can change very easily, and there are now a considerable number of constant voltage power sources, such as 12V and 24V LED drivers. A linear regulator wastes a lot of power, so the light can’t be as bright as it could be with a switching power supply.

High-efficiency switching supplies naturally lead to high light efficacy, which is the most important thing for most light applications. Also, switching power supplies flicker less, have a higher power factor, and can handle surges better than AC LEDs.

• Isolated LED Drivers vs. Non-Isolated LED Drivers

When we compare these two things, we call each of them a switching power supply. According to UL and CE regulations, the isolated design usually works at 4Vin+V and Vac, and the input and output voltages are well separated. Using a highly insulated transformer instead of an inductor as the part that transfers human power makes the system safer. Still, it also makes it less efficient (by 5%) and more expensive (by 50%). Insulation keeps the high voltage from going from the input to the output. On the other hand, low-power built-in designs usually use non-isolated designs.

• Constant Voltage vs. Constant Current LED Driver

Because LEDs have unique V-I characteristics, it goes without saying that a constant current source should power them. However, a constant voltage LED driver can be used if a linear regulator or resistor is connected in series with the LED to limit the current. Signs and strip lighting usually use constant voltage LED drivers with 12V, 24V, or even 48V because they are much more efficient than constant current LED drivers, which are the norm for general lighting like bulbs, linear lights, downlights, street lights, etc. As long as the total wattage doesn’t exceed the power supply’s limit, the constant voltage solution makes it easy for users to change the amount of light, giving it much flexibility for installation in the field.

• Class I vs. Class II LED Driver

In this case, I and II are written in Roman numerals instead of 1 and 2, which means something completely different, as you can see in the next item. IEC (International Electro-technical Commission) regulations use the terms Class I and Class II to describe how a power supply is built on the inside and how it is electrically insulated to keep users from getting an electric shock. IEC To keep people from getting shocked by electricity, Class I LED drivers must have protected earth connections and essential insulation. There is no need for a protected earth (ground) connection because IEC Class II input models have extra safety features like double or strengthened insulation. Class I LED drivers often have a ground connection at the input, while class II drivers don’t. However, class II drivers have higher insulation levels from the input to the enclosure or the output. And here are the most common symbols for classes I and II.

• Class 1 vs. Class 2 LED Driver

The Arabic numbers 1 and 2 stand for the NEC (National Electric Code) ideas of class 1 and 2, respectively. These ideas describe the output of a power supply with less than 60Vdc in a dry location and 30Vdc in a wet spot, less than 5A current, and less than 100W power, as well as the detailed requirements for the circuit design feature. Using class 2 LED drivers has a lot of benefits. Their output is considered to be a safe terminal, so no extra protection is needed at the LED modules or light fixtures. This saves money on insulation and safety tests. UL and UL set the rules for Class 2 LED drivers. But because of these limits, a Class 2 LED driver can only power a certain number of LEDs.

• Dimmable vs. Non-Dimmable LED Driver

In this new time, every light is made to be dim. This is a big subject because there are many ways to dim lights. Let’s talk about each one in turn.

1) 0-10V/1-10V dimming LED Driver

2) PWM dimming LED Driver

3) Triac dimming LED Driver

4) DALI dimming LED Driver

5) DMX dimming LED Driver

6) Other Protocols of LED Driver

• Waterproof vs. Non-Waterproof LED Driver

IEC uses the IP (ingress protection) certification as the only way to classify the degree to which LED drivers are waterproof. The IP code is made up of two numbers. The first number rates the protection against solid objects on a scale from 0 (no protection) to 6 (no entry of dust), and the second number rates the protection against liquids on a scale from 0 (no protection) to 7. (8 and 9) don’t come up very often in the lighting business. LED drivers with IP20 ratings or lower are used inside, while waterproof drivers are used outside. But this doesn’t always happen. For example, some indoor applications use waterproof LED drivers because they can put out much more power than low IP ones without needing an active cooling system, making them last less than IP-rated LED drivers.

What Is A Ballast And Why Are They Not Used In LED Lights?

When light bulbs were made for the first time, they had a mechanism inside them. The job of this thing was to slow down the flow of electricity through a circuit. Ballast is the name of this thing. If this wasn’t used in light bulbs and T8 light bulbs, there was still a chance that too much electricity could build up (tube lights). Ballast is still used in bulbs and tube lights to keep the current from getting too high. Ballasts are also often used with HID, metal halide, and mercury vapor lights.

• Magnetic Ballast 

Inductors, also called magnetic ballasts, give some lamps the right electrical conditions to start and run. Act as a transformer, giving out clean and accurate electricity. Even though it was made in the s, it was used from the s to the s. You can find them in High-Intensity Discharge (HID) lamps, Metal Halide lamps, mercury vapor lamps, fluorescent lamps, neon lamps, and so on. Before LEDs started to replace this technology around , it was used in almost all important parking lots and street lights for about 30 years.

• Electric Ballast

In an electric ballast, a circuit is used to limit the load or amount of current. Electronic ballast tries to keep the flow of electricity more steady and accurate than magnetic ones. People started using these more in the s, and they are still used today. 

• Function Of A Ballast 

A ballast controls how much electricity goes to the bulbs and gives them enough power to turn on. Since lamps don’t have control, they can use too much or too little electricity on their own. The ballast ensures that the amount of electricity going into the lamp doesn’t exceed what the light’s specifications allow. Without a ballast, a light or bulb will quickly draw more and more electricity, which could get out of hand.

When a ballast is put into a lamp, the power is stable, and the ballast controls the energy so that the current doesn’t go up even when the lights are connected to high-power sources.

• Why Don’t LEDs Use A Ballast?

LEDs don’t need a ballast for several reasons. First of all, LED lights don’t use much electricity. Also, you need an AC-to-DC converter since LEDs usually run on Direct Current (DC). The socket must be wired directly when switching to LED corn light bulbs. Lastly, because LEDs are much smaller than bulbs and tube lights, there is no extra space for ballast to fit. LED drivers can be made to take up much less space. Some experts also think that because LEDs don’t need a ballast, they use less energy and give off more light.

• Ballasts vs. LED Driver

LED and fluorescent lights can’t work without a converter between the bulb and the power source. On one hand, standard incandescent lamps heat a filament with electricity to make light. LEDs, on the other hand, use led drivers instead of ballasts. Ballasts and lead drivers do many of the same things, so getting them mixed up is easy.

This is made possible by fluorescent ballasts, which send out a high-voltage spike at the start of the lamp’s life. Once the light is turned on, this spike acts as a current regulator. The led power driver changes the power source into a specific voltage and current, which then makes the LED light up. Both of them keep the light from being affected by the power source.

An LED driver is needed to change the alternating current into the direct current that LEDs need. LEDs can’t be powered directly by alternating current, so an LED driver is required to change it. Ballasts have changed a lot in how they are made and how complicated they are. Ballasts can run fluorescent lights but not LEDs or lights that use less energy. Several LED drivers seemed to have taken out the ballasts. Because it works better, the LED driver can do most of the things that the ballast does.

How To Use An LED Driver?

Instructions for setting up LED drivers

1. Make sure your LED driver works with both the LED systems you want to connect it to and the power source you want to use. Both the Amperage and Voltage ratings must be the same.
2. Make sure the driver won’t have to deal with problems in the environment that it wasn’t made to handle. For example, if you want to put LEDs outside, ensure the driver can handle water well enough.
3. Once you know which wires are positive and negative, you can unplug your socket from the grid.
4. Use screws of the correct color to attach the driver to the LED system.
5. Connect the positive and negative wires from the LED system to the right terminals on the driver.
6. Connect a grounding terminal to the green grounding wire coming from the driver (the GND).
7. Connect the positive and negative wires from the power socket to the positive and negative terminals on the driver.
8. Check the installation carefully to ensure that all the connections are tight and in the right place and that heat is not building up. If something goes wrong, turn off the power and figure out what’s wrong.

How To Repair An LED Light Driver?

1. Turn the power off.
2. Open the driver with a screwdriver and look carefully for burn scars and other flaws that are easy to see.
3. Use electrical testing equipment to find the parts that are broken.
4. If you can, switch out these parts and test the device again. If it can’t be done, the whole driver has to be changed.

Factors To Consider Before Choosing An LED Driver

• DC Dimming

Would you like LEDs to be less bright? Or do you plan to change how bright it is? Then choose a dimmable driver or power supply. Why? The power sources are easy to tell apart because of how they work. The specifications table also has extra information, like what kinds of dimmer controls can be used with the drivers.

• Power Requirements

One of the first things to consider is how much voltage your lamp needs. So, if your LED needs 20 volts to work, you should buy a 20-volt driver.

In short, the goal is to ensure that your driver gets the right amount of power. The general rule is that you should do your job within the range of the light.

For a constant-voltage driver, you can also think about the voltage range. But you can measure both voltage and current ranges with a constant-current driver.

Pay attention to how much voltage the proposed LED light will use. So, ensure the LED driver can handle the voltage from the LED. In this way, it is easy to step down to the needed output voltage.

Also, you should think about watts. During this process, make sure to buy a driver with a higher maximum wattage than the light.

• Power Factor

The power factor helps determine how much power the driver uses from the electrical network. And the range is usually from -1 to 1. Since this is the case, a power factor of 0.9 or more is the norm. In other words, as the number gets closer to one, the driver works better.

• Safety

Your LED drivers should meet several different standards. For example, we have UL classes 1 and 2. Use the UL Class 1 for drivers that put out a lot of voltage. The fixture needs to be set up safely for drivers in this group. It can also hold more LEDs, which makes it work more efficiently.

At the level of LEDs, the UL Class 2 drivers don’t need a lot of safety features. It also meets the standards set by UL. Even though this class is safer, it can only run a certain number of LEDs at a time.

The IP rating is another way to measure how safe a driver’s cage is and what it can do. If you see IP67, for example, it means that the driver is safe from dust and brief immersion in water.

• Efficiency

This part is crucial because it shows how much power the LED driver needs. The value is shown in terms of percentages. So, you could expect it to work between 80% and 85% of the time.

Benefits Of An LED Driver

Low voltages of 12 to 24 volts power LEDs with direct current. So, even if your AC voltage is high, between 120 and 277 volts, an LED driver will change the direction of the current. In other words, stepping down from alternating to direct current is helpful. You can even find the right amount of high and low voltage.

LED drivers keep LEDs safe from changes in voltage or current. If the voltage of an LED changes, the current supply may change. Because of this, LED lights’ output is inversely related to how many they have. LEDs are also only supposed to work within a specific range. So, too little or too much current will change how much light comes out or cause the LED to break quickly because it gets too hot.

Overall, LED drivers have two main benefits:

Eaglerise contains other products and information you need, so please check it out.

1. Changing from AC to DC.
2. The drivers help ensure that a circuit’s current or the voltage doesn’t drop below its rated level.

Does New Illuminant Equal New Dimming?

Other light sources can be turned off quickly by changing the voltage, but LEDs can only be turned off by changing the ratio of voltage to current. Because of this, there are different ways to dim LEDs:

• With pulse width modulation (PWM) or pulse duration modulation (PDM), the amount of time that voltage is given can be changed (PDM). However, the voltage itself does not change. In other words, PWM quickly turns the LEDs on and off. This happens a lot when the frequency is above 100 Hz. The brain thinks the room is darker because the human eye can’t tell flickering is happening until at least 75 Hz.

• Triacs and phase control dimmers were first made for 60W incandescent bulbs, which give off a low amount of light when the phase angle is 130°. On the other hand, LEDs are much better and use much less electricity to light up. Because of this, LEDs are not very dim at a phase angle of 130°. Also, the holding current may not be enough to keep the triac in the conductive state when the dimming is high. Because of this, LEDs start to flicker. Still, some LED drivers are built on the inside to get around this problem.

• 1-10V: In the 1-10V method, ballasts and control units are connected by a polarized two-wire control line. DC voltages between 1 and 10 volts are used to control the light, and as the voltage increases, so does the light’s brightness. You can dim LED elements with 1-10V, but they need power sources. The control unit must also be able to take in the current that the power supply sends through the control line. So, 1-10V dimming is a better choice for large lighting systems.

When Does An LED Driver Become Necessary?

Most of the time, every LED light source needs a driver. But the main question should be, “Do I have to buy one separately?” The problem is that some LED light bulbs have a driver built right in. Also, LEDs made for home use often come with LED drivers. And a great example is 120-volt bulbs with bases that are either GU24/GU10 or E26/E27.

Low-voltage LEDs, such as tape lights, MR bulbs, outdoor-rated lights, panels, and other lighting fixtures, need an LED driver to work correctly.

When working with low-voltage LEDs, you need LED drivers. But you can’t say the same about 120-volt LED bulbs used in homes.

Print Mounting And HighBay Mounting

LEDs can be put in HighBay mounting and print mounting in several ways, depending on the project’s needs: For example, so-called SMD (surface-mounted device) LEDs can be used in tighter spaces. Because they can be soldered onto printed circuit boards, they don’t need wires. Still, check to make sure that all of the parts fit together.

In bigger rooms, there needs to be more light. Because of this, factory halls and department stores use HighBay spotlights, which are powerful ceiling lights. These have to be wired separately, but they are very strong. They can be wired to the standard mains voltage of 230V AC. To keep the LEDs from getting too hot, drivers like the XBG-160-A are connected in front of them. These have protection against overload that can actively limit how much current is sent.

LED Driver Types

• Constant-Current

This LED driver only needs a fixed amount of output current and a range of output voltages. Constant current is a specific output current measured in milliamps or amps and has a range of voltages that change depending on how much the LED is being used (its wattage or load).

• Constant-Voltage

Constant-voltage LED drivers have a constant output voltage and a maximum output current. The LED module also has a regulated current system that a simple resistor or an internal constant-current driver can power.

They only need a single steady voltage, usually 12 or 24 volts DC.

• LED Drivers For AC

Theoretically, this LED driver could run halogen or incandescent lights with low voltage. But standard transformers can’t be used with AC LED drivers because they can’t tell when the voltage is low. So, they have transformers that don’t have a minimum load.

• Dimmable LED Drivers

With these LED drivers, you can dim your LED lights. It also lets you control the brightness of LEDs with a constant voltage. And it does this by reducing the amount of current that goes to the LED light before it turns on.

Applications Of LED Drivers

• Automotive LED Drivers

With high-quality automotive LED drivers, you can tell the difference between your car’s inside and outside lighting systems in many ways:

1. The group of headlights
2. infotainment 
3. Interior and rear lighting 

• Backlight LED Drivers

LCD backlight LED drivers often use a specific dimming scheme to control the backlight’s brightness.

• Illumination LED Drivers

You can set up your devices with LED drivers to have infrared lighting. It can also be done with the help of a multi-topology constant-current controller.

• RGB LED Drivers

With RGB LED drivers, you can add an animation or an indicator to your LED arrays with more than one color. Also, they often work with many standard interfaces.

• Driver for LED displays

With the help of LED display drivers, you can control which LED strings use the least and most power. So, these drivers can be used with either a large narrow pixel or a matrix solution for small or mini LED digital signage applications.

What LED Driver Do I Need?

To figure out what size LED driver will meet your needs, you need to know the following:

1. The voltage of the mains power that you’ll be using
2. The total amount of power that the system’s LEDs use
3. What kind of voltage or constant current do the LEDs need

If there are any other technical factors, like the need for precise color control or the possibility of water exposure, that can affect how the LED drivers work. The LED’s IP rating shows how resistant it is to water; a higher rating means it is more resistant. With an IP rating of 44, the product can be used in kitchens and other places where water might occasionally splash on it. A driver with a high IP rating, like 67, can be used outside. Drivers with an IP rating of 20 should only be used inside, where it’s dry.

More information, you can read How To Choose the Right LED Power Supply.

FAQs

Summary

LED drivers are used in many different industries, just like LEDs. You can also light your space with the wide range of transformers, power supplies, and drivers available. Because LEDs are so flexible, adding smart features and changing the brightness is easy. In this way, LED drivers are essential to making modern, practical, and cost-effective lighting.

What does an LED driver do? LED drivers have a similar function to transformers for low voltage bulbs. LED lights are primarily low Voltage devices - typically 4v, 12v or 24v - and are designed for a direct current power supply. However, most wall socket power supplies are not directly compatible as these usually run at a much higher Voltage (between 120 and 277V) and supply alternating current. As the average Voltage of an LED is too low for a conventional transformer, specialist LED drivers are used to convert high voltage alternating current to low voltage direct current.

LED drivers have the secondary function of preventing power surges and fluctuations, which can cause high temperatures and affect light output. LEDs are designed for use within a strict predetermined amp range.

Some LED drivers can also be used to control and sequence the brightness of the LED systems attached and the colours which are displayed. This is done by selectively switching individual LEDs on and off. White lights, for example, are usually created by displaying LEDs of multiple colours at once - switch some of these off via the LED and the white colour is no longer visible.

Constant current LED drivers are used with LEDs that require a steady current but varying Voltages as the wattage (total power load) in each LED changes. The driver is responsible for varying the Voltage.

The principal amperage ratings for constant current LED drivers are:

• 350 milliamps (mA)
• 700mA
• 1 amp

A typical configuration might be the supply of a 700 milliamps (ma) current as the Voltage varies between four and 13 volts in response to a 50-watt load.

These devices are also known as constant power LED drivers. Typical uses include:

• Illuminating outdoor features
• High definition displays for use in public spaces
• Backlighting for billboards

By contrast, constant Voltage LED driver circuits are designed for LEDs that need steady Voltage - typically 10V, 12V or 24V DC. This makes them best suited to LEDs arranged in a line or string - e.g. lighting strips or similar configurations parallel to the driver. Normally LED strip drivers have a separate resistor for each LED in the strip - this is known as a current limiting resistor.

Like all components, LED drivers are available in a variety of models with differing specifications. Amongst other factors, available input and output levels vary between models, along with efficiency, power ratings, and the amount of environmental shielding (ingress shielding) applied to protect the connection terminals.

Let’s look at a few of the principal models available:

Small LED Drivers

Small or mini LED drivers are designed for use with smaller LED lights. A 4-watt rating would be typical.

Dimmable LED Drivers

Dimmable LED drivers allow users to dynamically adjust the brightness of LEDs. Adjustable LED drivers are a useful way to create mood lighting in public spaces such as shops.

High Power LED Drivers

The power of LEDs is growing steadily - some professional models now offer as much as 100 lumens per watt. Lumens are an internationally recognised unit of visible light. These high-power models are widely deployed in the larger lighting systems used in commercial and public spaces. Naturally, these require more powerful LED drivers or turbines to ensure smooth operation.

COB LED Drivers

Chip on board (COB) LEDs consist of multiple LEDs in a cluster alongside integrated circuitry. Typically, they include a dimming function. You will require a compatible driver or transformer with a sufficient Voltage rating. Both constant current and constant voltage drivers are compatible with COB LED drivers but constant current models are easier to apply.

LED String Driver

LED strings normally feature smaller lights. They are typically used for mood lighting effects - for example, Christmas lights. Mini LED drivers are the best choice for these, although the total Voltage requirements may climb for longer strings.

How to Connect an LED Driver to Power

Although wiring an LED driver to mains power is straightforward, we would recommend that a qualified electrician inspects this to make sure the connections have been made safely.

The process of connecting an LED driver to power consists of connecting the neutral and line wires to the PRI (primary) side of the driver, attaching the former to the N terminal and the latter to the L terminal. The positive and negative wires should then be taken from the LED lighting and attached to the matching terminals on the SEC (secondary) side of the driver.

How to Wire LED Drivers and Transformers

Often, LED drivers and transformers do not include terminals, and so users must directly wire a plug to the end of the cable. Please note that wiring should only be carried out by trained and qualified individuals.

1. Check the LEDs are in place and turn off the power
2. Open the driver or transformer using a screwdriver
3. Connect the plug using suitable cabling and wire nuts (colour-coded cabling screws). The black positive cable from the transfer should be connected to the 120V AC feed in the socket, the green cable to the grounding wire and the white negative wire to the neutral connection. It may be necessary to strip back one end of the LED cabling, depending on the brand
4. Apply terminal connectors to the cabling for a firm hold
5. If necessary, terminate the positive and negative wires that connect to integrated circuitry in the driver or transformer
6. Close the unit and test it in a well-ventilated area

How to Test an LED Driver

There are three standard ways to test that an LED driver is functioning correctly:

1. Connecting it to the LEDs and observing the results
2. Using electronic load testing equipment - trying, for example, constant resistance (CR) or constant voltage (CV) modes
3. Applying a load resistor (a device that impedes current) to assess the power supply

Once again, if in doubt, please do not attempt to test the component and consult a fully qualified engineer instead.

How Many LEDs Per Driver?

The total number of individual LEDs is less important than the total power they require.

To work correctly and have a reasonable lifespan, LEDs require the right amount of wattage. Too much will cause them to burn out, while too little will prevent them from working at all. But the driver components can also be stressed by power-hungry LEDs.

Therefore, drivers should ideally not be connected to LEDs that consume more than 80% of the driver’s maximum output. For example, a driver with a maximum output of 50 Watts should be attached to LEDs with a maximum collective output of 40 Watts.

What is the Difference Between an LED Driver and a Transformer?

LED transformers have a higher power output and so are used with larger LED lighting systems - for example, longer strips - which require higher Wattage levels than that provided by LED drivers to operate correctly and safely.

What is an LED Driver IC?

An LED driver integrated circuit (IC) provides the processing power necessary to allow it to respond to the changing power demands of the attached LEDs.

Do I Need a Transformer for LED Lights?

To work out whether you need a driver or a transformer, multiply the length of the system by the Watts required per metre, for example:

10 metres x 30 Watts per metre = 300 Watts

This exceeds the maximum Wattage output of an LED driver (200 Watts), so a transformer will be required. The collective power requirement of an LED system should be less than the transformer’s maximum capacity.

Can LEDs Work on AC?

Sometimes. Most LEDs are built to run on low power direct current (DC) but some high capacity models have been developed which do run on alternating current (AC).

Want more information on Isolated led drivers? Feel free to contact us.